# Commercial Heat Pump Installation in Aurora, CO

> Commercial heat pump installation in Aurora, CO, planned around how the building is used: existing equipment, electrical service, controls and phased work.

URL: https://sundogauroraheatpumps.com/commercial-heat-pump-installation/

Offices, shops and multifamily buildings can't close for a week. We start with how the building is used, then shape the system and the schedule around it.

- Planned around building use and occupants
- Priced line by line on the written estimate
- Aurora reviews new electrical permits under the 2026 NEC from August 1, 2026

A commercial building has people in it on a schedule: tenants who need heat by Monday morning, a shop floor with the doors open half the day, apartments where someone is always home. Sundog plans and installs commercial heat pumps for offices, shops and multifamily buildings in Aurora, and the plan starts with that schedule rather than with the equipment.

From there we look at what is already on the roof or in the mechanical room, what the electrical service can carry, and how the controls run the building today. Each one changes the system you get and the order the work happens in. Commercial jobs vary too much for one price band, so the written estimate lists what sets your price, line by line.

## Swapping four rooftop units without closing an office

Greenwood Village: Rooftop heat pump units on curbs on a flat office roof.

The same scene in a thermal view.

Project price

Quoted after a roof and electrical survey

On site

8 working days over four weekends

Where

Greenwood Village

The house

1990s two-story office, four tenant suites

Commercial heat-pump work is mostly about sequence. This 1990s Greenwood Village office, two stories and about 14,000 square feet, ran four gas rooftop units of roughly 5 tons each, one per tenant suite. Heat exchangers were rusting, economizers were seized and refrigerant leaks kept coming back. No tenant was able to close for a week.

We phased the job over four weekends, one suite's unit at a time. On Saturday the parking lot closed, a crane lifted the old unit off and a packaged heat-pump rooftop unit went on. The new units didn't match the old curb footprint, so fabricated, insulated curb adapters went on and were flashed to the existing membrane rather than new roof openings being cut. On Sunday we connected power and ductwork, capped the gas and commissioned the unit, so the suite opened on Monday with heating and cooling.

The electrical review before ordering changed part of the plan. With electric backup strips, two of the four units needed more circuit than their feeders carried on the 208-volt service. An electrician upsized those two feeders and disconnects during their phases. New suite thermostats were set to run on occupancy schedules agreed with the property manager and lock the strips out above a set outdoor temperature.

The city inspected each phase before the next unit came down.

## What happens on the first visit

We walk the building with whoever runs it day to day, usually the owner or the property manager, and look at four things before we suggest a system.

### How the building is used

Hours, occupancy, which spaces run hot or cold, ventilation needs, and which tenants or rooms can never lose heat or cooling during work.

### What is installed now

Rooftop units, split systems or ductless heads: their age, nameplates, roof curbs, duct connections and the condition of what stays, such as ducts and dampers.

### Electrical service

Voltage and phase, feeder and disconnect sizes, and room in the switchgear. Electric backup heat often decides whether a feeder needs upsizing.

### Controls, roof and access

Thermostats or a building automation system, economizers and schedules, plus roof structure, crane setting space and ladder or hatch access.

## Phasing the work around occupants

The schedule shapes the scope as much as the equipment does. We break the job into phases that each leave the occupied spaces with heating and cooling, then agree the order and dates with the property manager.

1. Why phases, not one big weekend Crane time, roofing and electrical work all add hours. Splitting a building into phases keeps any overrun inside one suite instead of the whole building, and each finished phase proves the plan before the next one starts.

## Choosing the system for the building

Small commercial buildings commonly run on packaged rooftop units or split systems. A heat pump can usually take the same place, but the choice depends on what the building already has.

### Packaged rooftop heat pumps

They replace gas or electric rooftop units in the same spot. New units rarely match old curb footprints, so we use fabricated curb adapters flashed to the existing roof where the structure allows, rather than cutting new openings.

### Split heat pumps

An indoor air handler on the existing ducts with an outdoor unit on the roof or at grade. They suit mechanical rooms, retail spaces and buildings where rooftop work is hard.

### Ductless and multi-zone

Heads in individual offices, apartments or a server closet. They give each space its own control and suit buildings without good duct runs. Our [ductless page](https://sundogauroraheatpumps.com/ductless-mini-split-installation/) covers head placement and drains.

## Electrical service and backup heat

Commercial heat pumps usually run on three-phase service, and the outdoor sections alone often fit the existing circuits. Electric backup heat is what changes the math.

### Backup heat on the feeder

Heat strips sized for the coldest hours add a large load to each unit. We review the service before ordering, because an undersized feeder found on installation day stops the phase. Our [backup heat guide](https://sundogauroraheatpumps.com/guide/heat-pump-backup-heat/) explains how strips are staged and locked out.

### Cold-weather output

We select equipment from its published heating output at low outdoor temperatures, so the backup covers the gap rather than the whole building. The [cold-climate page](https://sundogauroraheatpumps.com/cold-climate-heat-pump-installation/) and our [cold-weather performance guide](https://sundogauroraheatpumps.com/guide/cold-weather-heat-pump-performance/) cover the numbers.

## Controls, ventilation and commissioning

A new heat pump on old controls wastes much of what it can do. We set controls up for how the building actually runs.

### Controls and schedules

Occupancy schedules, setbacks, backup heat lockout above a set outdoor temperature, and economizer settings, agreed with the property manager and set after the last phase. Where a building automation system exists, we confirm how the new units connect to it.

### Commissioning each unit

Each unit is started, its airflow, charge, defrost and backup checked, and its readings recorded before the next phase begins. The property manager keeps a commissioning record for every unit.

## Permits and inspections

Aurora has adopted the 2021 International Building, Mechanical, Fuel Gas and Energy Conservation Codes, and reviews new electrical permits under the 2026 National Electrical Code from August 1, 2026. A commercial heat-pump job usually needs mechanical and electrical permits, and often roofing and crane or lot-closure coordination. Many buildings near Aurora sit in a neighboring city or county, so we confirm the permit authority for each address. Fees are set by scope through the city's fee schedule and calculator, and we build inspections into the phase plan. Our [installation process guide](https://sundogauroraheatpumps.com/guide/heat-pump-installation-process/) shows where permits and inspections fall in a job.

## What sets the price of commercial work

Sundog prices commercial heat-pump work building by building, because two buildings with the same square footage can need very different jobs. These are the lines that set your price on the written estimate.

| Part of the price | What sets it |
| --- | --- |
| Equipment | Building load, number of units or zones, cold-weather output, economizers |
| Curbs and roof | Curb adapters, flashing, roof structure, roofing sign-off where a roof warranty applies |
| Crane and access | Crane size and hours, lot closure, hatch or ladder access |
| Electrical | Feeder and disconnect upsizing, backup heat, switchgear room |
| Gas removal | Capping and removing gas lines to retired units |
| Controls | Thermostats or building automation integration, schedules |
| Phasing | Number of phases, weekend or after-hours work |
| Permits and commissioning | Permit scope, inspections per phase, commissioning records |

## Commercial incentives

Xcel Energy has temporarily paused payment of its Colorado commercial heat-pump rebates. Completed applications can still be submitted, and the amount depends on what is available at submission and on the project dates. We check the current status for each building case by case and list what an application needs, but we don't count on a rebate payment when we price the job. Residential programs work differently; our [rebate guide](https://sundogauroraheatpumps.com/guide/heat-pump-rebates-aurora/) covers those.

## What is included in a commercial installation

- A building walk-through covering use, existing equipment, electrical service, controls and access
- A phase plan agreed with the owner or property manager before ordering
- Equipment with model numbers and low-temperature capacity on the estimate
- Removal of old units, with refrigerant recovered and gas lines capped
- Curb adapters or new mounting, flashed and sealed
- Electrical work for each unit and its backup heat, with the permits
- Controls and schedules set up with the property manager
- Each unit commissioned before the next phase, with a record for every unit

## Rooftop, split or ductless

|  | Packaged rooftop heat pump | Split heat pump | Ductless multi-zone |
| --- | --- | --- | --- |
| Best fit | Replacing existing rooftop units | Mechanical room or grade-level outdoor space | Individual offices or apartments, weak duct runs |
| Main changes | Curb adapters, feeders, controls | Air handler, line sets, outdoor pad or stand | Heads, line sets, condensate in each space |
| Main checks | Roof structure, curb fit, electrical service | Duct static pressure, line routes | Space loads, head placement, drains |
| Price | Set by the lines above | Set by the lines above | Set by the lines above |

## How the job runs

1. **Walk-through** use, equipment, power, controls
2. Written estimate and phase plan
3. **Permits** mechanical, electrical, roofing
4. **Install** phase by phase
5. Commissioning and city inspection

## Related planning

Many commercial jobs are replacements of aging equipment; our [replacement page](https://sundogauroraheatpumps.com/heat-pump-replacement/) covers how we size a new system from the load rather than the old nameplate, and the [electrical panel guide](https://sundogauroraheatpumps.com/guide/electrical-panel-for-heat-pump/) covers circuits and backup heat. If a unit has failed and you need it running before a phased plan, start with [heat pump repair](https://sundogauroraheatpumps.com/heat-pump-repair/).

Tell us about the building and how it is used. Call [(719) 417-2475](tel:+17194172475) or [request a walk-through](https://sundogauroraheatpumps.com/contact/).

## Commercial heat pump installation in Aurora

Planned around the people in the building, phased so no one goes without heat or cooling.

## Related resources

Backup heat

Backup heat covers the hours a heat pump cannot carry the house alone.

Electrical panel

Not always. The answer comes from the nameplate on the new equipment, what is already on your panel and a load calculation, not from the panel's size alone.

Cold-weather performance

A heat pump keeps heating when it is cold outside, just with less output as the temperature drops.

## Questions about commercial heat pump installation

### Can a heat pump heat a commercial building through an Aurora winter?

Yes, with equipment chosen by its low-temperature output and backup heat sized for the coldest hours. We work out how much of the winter the heat pump carries before you decide.

### Can rooftop units be replaced without cutting new roof openings?

Usually. Fabricated curb adapters fit the new units to existing curbs, provided the roof structure carries the new weight. We check both on the walk-through.

### Can tenants stay open during the work?

That is what phasing is for. We plan phases, often over weekends, so each occupied space has heating and cooling when it opens, and agree the dates with the property manager.

### Is there a rebate for commercial heat pumps?

Xcel has temporarily paused payment of its Colorado commercial heat-pump rebates. We check the current status for your building and list what an application needs, without counting on a payment.

### What does the written estimate include?

Model numbers and low-temperature capacity, duct and electrical work, the permit, removal, the pad or stand and the start-up checks, each on its own line.

## Related services

Heat pump replacement

When a heat pump or AC starts failing, we put the repair and the replacement side by side, then size any new system from the house rather than the old label.

Cold-climate heat pump installation

We choose cold-climate equipment from what it puts out at 5°F, size backup heat to the hours it falls short and set the outdoor unit where snow and meltwater cannot stop it.

Heat pump repair

Cool air in heat mode, ice that will not clear, a breaker that trips.

## Commercial heat pump installation in Aurora

Measured first, sized to the house, every item in writing.
