# Can my ductwork handle a heat pump?

> What a heat pump needs from your ducts in Aurora: airflow per ton, static pressure, returns, filters and leaks, and when duct changes come before equipment.

URL: https://sundogauroraheatpumps.com/guide/ductwork-for-heat-pumps/

Most Aurora houses with a furnace already have ducts a heat pump can use. Whether they can carry its airflow is a measurement, not a guess.

Usually, yes. Your ducts can handle a heat pump if they carry the airflow it needs, typically around 350 to 450 cubic feet per minute per ton, at a static pressure the blower can work against. Many residential blowers are rated at 0.5 inches of water column. A weak return, crushed flex or leaky joints are the usual problems, and most are fixable.

Every Sundog estimate visit includes a static-pressure reading and a look at returns and leaks, and any duct work we find goes on the [written estimate](https://sundogauroraheatpumps.com/heat-pump-installation/) as its own line.

## Why a heat pump is fussier about ducts than a furnace

The difference comes down to the temperature of the air in the ducts.

### A gas furnace

Delivers very hot air, so even a reduced airflow still carries plenty of heat. Tired ducts hide behind it for years.

### A heat pump

Delivers air that is warm rather than hot, so it needs its full airflow to move the same heat. Lose a third of the air to a restricted return and the far bedrooms feel it straight away, and the equipment works harder. Our [cold-weather guide](https://sundogauroraheatpumps.com/guide/cold-weather-heat-pump-performance/) explains the supply temperatures.

## What we measure on the visit

Duct condition is judged from readings and a look at the system, starting at the blower and working out to the rooms.

- Total external static pressure at the blower, the single best summary of how hard the ducts are to push air through
- Return size and the number of returns, compared with the airflow the new system needs
- The filter rack: filter size, type and whether air slips around it
- The supply trunk and far runs for leaks, crushed or kinked flex and disconnected joints
- Ducts in attics, crawlspaces or garages, where leaks and missing insulation cost the most
- Which rooms run hot or cold, and what the owners already notice

## Reading static pressure

Static pressure is measured in inches of water column. Lower means the ducts let the air through.

### Near the rating

A reading near the blower's rated pressure, often 0.5, means the ducts can carry full airflow. The heat pump goes in without duct changes, or with small sealing work.

### Well above it

A reading near 0.8 or higher means the blower is fighting the ducts. On the Littleton job on our [ducted installation page](https://sundogauroraheatpumps.com/heat-pump-installation/) the reading was about 0.9 before the return was fixed.

## The usual fixes, and how to spot the problem

When the reading is high we find out why before anyone orders equipment. These are the usual causes, and each fix goes on the estimate as its own line so you can see what it costs and why it is there.

| Problem | What you notice | The fix |
| --- | --- | --- |
| Undersized return | Whistling grille, cold far rooms, a loud blower | A larger return or a second return upstairs |
| Crushed or sagging flex | One room never keeps up | Replace the run, often with rigid round duct |
| Leaky trunk joints | Dusty basement, uneven rooms | Seal joints with mastic or foil tape |
| Restrictive filter | High reading that drops with the filter out | A larger filter rack or a lower-resistance filter |
| Dirty indoor coil | Weak airflow everywhere | Coil cleaning, or replacement with the system |

## When duct changes are worth it, and when they aren't

Duct work is evaluated against what it fixes. Not every house needs it, and some problems are cheaper to solve another way.

### Worth doing before install

A high static reading, a single small return, or crushed runs to the rooms that already complain. These fixes let the new system deliver its rated airflow.

### Worth weighing

Long runs to a room over the garage or an addition that was never on the duct system. A single [ductless head](https://sundogauroraheatpumps.com/ductless-mini-split-installation/) may serve that room better than a new duct run; the [ducted vs ductless guide](https://sundogauroraheatpumps.com/guide/ducted-vs-ductless-heat-pump/) compares them.

### New ductwork

New runs are laid out with ACCA's Manual D method so each room gets the air its load calls for. That is a bigger job and priced separately.

## Flex or rigid metal duct?

Both are allowed; how they are installed matters more than which one is used.

### Rigid metal

Smooth inside, holds its shape and resists crushing. We favor it for returns and the trunk, where airflow is greatest.

### Flex

Fine for short branches when pulled tight and supported. Long, sagging or kinked flex is a common airflow problem in older ranches and tri-levels.

## Ducts in the attic, crawlspace or garage

Ducts that run through unheated space lose heat before it reaches the room, and a heat pump's warm-not-hot air has less to spare.

### Where it shows up

Tri-levels and split-levels often run returns through a crawlspace, and rooms over garages are fed through cold framing. Leaks there pull cold air into the return or push warm air into the crawlspace.

### What helps

Sealing the joints first, then insulating the runs that sit in cold space. The load calculation counts duct location, so fixing it can also trim the size of the system you need.

## Know your ducts before you compare equipment

Two quotes for the same heat pump can perform very differently if only one fixes the return. Call Sundog at [(719) 417-2475](tel:+17194172475) or [book a visit](https://sundogauroraheatpumps.com/contact/) and we will measure your ducts first. For sizing, see [heat pump sizing](https://sundogauroraheatpumps.com/guide/heat-pump-sizing/); for the whole plan, the [Aurora planning guide](https://sundogauroraheatpumps.com/guide/aurora-heat-pump-planning-guide/).

## Questions people ask

### Do I need new ducts for a heat pump?

Rarely the whole system. Most Aurora houses need, at most, a larger or second return, a replaced run or sealing. We measure before recommending anything.

### How often should I change the filter with a heat pump?

Check it monthly in heating and cooling season and change it when it looks gray, or at the interval the filter maker gives. A clogged filter raises static pressure and cuts airflow.

### Will a heat pump fix a room that is always cold?

Only if the cause is fixed with it. A cold room usually traces to a restricted run, a leak or a weak return, which the visit finds.

## Related service

Ducted heat pump installation

Before we recommend a heat pump, we measure the house: room by room for the load, at the blower for airflow, at the panel for capacity.

## More guides

Aurora heat pump planning guide

The whole decision in the order it gets made: how a ducted heat pump works, what it does in the cold, how it is sized, what happens to your furnace, ducts and panel, and what it costs to buy and run.

Heat pump sizing

Size comes from what your house loses on a cold night and gains on a hot afternoon, matched to equipment by its output in the cold.

Cold-weather performance

A heat pump keeps heating when it is cold outside, just with less output as the temperature drops.

Ducted vs ductless heat pump

Start with what is already in the house: the ducts, the rooms that give trouble and the panel.

Installation process

From the first visit to the city's inspection, here is the order of the work, what each step proves and what you should have in hand at the end.
