# Heat Pump Conversions and Installation in Sherrelwood, CO

> Heat pump installation in Sherrelwood, CO: we check 1960s panels and ducts first, then size a heat pump or dual-fuel system to the house. Typical ranges inside.

URL: https://sundogauroraheatpumps.com/service-areas/sherrelwood-cdp/

Older houses, small ducts and the panel they were built with. We measure all three before we recommend a heat pump.

Last Updated: November 2026

In Sherrelwood the question is rarely whether a heat pump can heat the house. It is whether the electrical panel and the ducts can carry one. Sundog plans heat pump installation in Sherrelwood starting from those two things: a load calculation on the panel, a static-pressure reading at the furnace and a room-by-room heat load, all on the first visit.

From there you choose between keeping your furnace as backup, going all-electric with a service upgrade, or adding ductless heads where the ducts fall short. Every option goes on the [written estimate](https://sundogauroraheatpumps.com/heat-pump-installation-cost/) with its own price.

## Where Sherrelwood calls usually start

The housing here is older than in most of the north metro, so the calls tend to circle the same few situations.

### The AC is failing and the furnace is fine

A heat pump replaces the AC and takes over most of the heating, while the furnace stays for the coldest nights. This is the most common [conversion](https://sundogauroraheatpumps.com/heat-pump-conversion/) path for a house with a younger furnace.

### The panel looks full

A 100-amp panel with a gas dryer often has room for one outdoor-unit circuit but not an electric backup strip. We work that out with a load calculation, not by counting empty slots.

### Some rooms never keep up

Duct systems from this era were sized for furnace air. A heat pump moves more air at a lower supply temperature, so a weak branch shows up fast. We read [static pressure](https://sundogauroraheatpumps.com/guide/ductwork-for-heat-pumps/) before we choose a size.

### The house heats with electricity now

About a quarter of Sherrelwood homes heat with electricity. Replacing resistance heat with a heat pump is a different job from a gas conversion, and the panel math changes with it.

## What we do for Sherrelwood houses

### Ducted and dual fuel

A [ducted heat pump](https://sundogauroraheatpumps.com/heat-pump-installation/) on your existing ducts, or a [dual-fuel system](https://sundogauroraheatpumps.com/dual-fuel-heat-pump/) that keeps the furnace as backup. We choose [cold-climate equipment](https://sundogauroraheatpumps.com/cold-climate-heat-pump-installation/) by its published output at 5°F, so the furnace runs fewer hours.

### Ductless, repair and upkeep

[Ductless heads](https://sundogauroraheatpumps.com/ductless-mini-split-installation/) for a converted garage, a basement bedroom or a room the ducts never reached. In a basement bedroom the lines usually run through the joist bays to an outdoor unit on the side yard. We also handle [heat pump repair](https://sundogauroraheatpumps.com/heat-pump-repair/) and yearly [maintenance](https://sundogauroraheatpumps.com/heat-pump-maintenance/) for systems already in place.

## How a Sherrelwood job usually runs

Each step leaves you with something in writing before the next one starts.

1. The visit Room loads, a static-pressure reading at the furnace, the duct runs you can reach, and the panel: its rating, what is on it and what it carries on a cold evening.
2. The options If the panel limits backup heat, you see two paths priced side by side: dual fuel on the panel you have, or all-electric with a service upgrade.
3. Permits Sherrelwood is unincorporated, so the mechanical and electrical permits come from Adams County, not a city. We confirm the permit path for your address before work is scheduled.
4. Install and start-up Old condenser out, coil and outdoor unit in, circuit wired, system charged and tested. Start-up readings, model numbers and rebate paperwork stay with you.

## What we look for in a Sherrelwood house

Three things about Sherrelwood shape most estimates here, and each one comes from the age and makeup of the housing.

### Housing from the late 1960s

The Census Bureau's American Community Survey puts Sherrelwood's median year built at 1967, among the oldest of the places we serve. Houses from that period often still have their original service size and duct layout. That tells us nothing certain about your house, but it tells us where to look first: the panel, the return and the far rooms.

### Mostly gas heat, with a real electric share

About 71% of occupied homes here heat with utility gas and about 25% with electricity. For the gas homes, the decision is usually how much of the heating the heat pump takes on. For the electric homes, a heat pump replaces resistance heat, and the panel calculation starts from what the old heaters already draw.

### County rules, checked per address

Sherrelwood is a census-designated place inside Adams County, with no city government of its own. For permits applied for from July 1, 2026, unincorporated Adams County uses the 2024 International Mechanical Code and the 2023 National Electrical Code. Fees and inspections follow the county's process, and we confirm both for your address.

## Dual fuel or all-electric on an older panel

Most Sherrelwood conversions come down to this choice, and the panel usually makes it. Here is how the two paths differ once the load calculation is done.

### Dual fuel on the panel you have

The heat pump needs one dedicated circuit, often 25 or 30 amps. The furnace stays as backup, so no electric strip is needed and the service size stays the same. It suits a furnace with years left and a panel with a little room. You keep a gas bill, and the changeover temperature decides how much of the winter runs on the heat pump.

### All-electric with a service upgrade

An air handler with an electric strip replaces the furnace, which takes far more panel capacity than the heat pump alone. On a 100-amp service that usually means an upgrade, and the utility has its own steps for that. We price the upgrade as a separate line so you can weigh it against keeping gas. Our [panel guide](https://sundogauroraheatpumps.com/guide/electrical-panel-for-heat-pump/) explains the circuits.

## Why we measure before we price

- A panel load calculation decides between dual fuel and all-electric before you spend money on either.
- Sizing from the room loads, not the old condenser label, keeps a small 1960s duct system from being asked for more air than it can move.
- Reusing an existing wall sleeve or line route where it is sound saves coring through brick or block.
- We price a service upgrade as its own line, so you can see what all-electric costs against keeping the furnace.
- Rebate eligibility depends on your address, equipment and installer path, so we check it before the estimate is final. See our [rebate guide](https://sundogauroraheatpumps.com/guide/heat-pump-rebates-aurora/).

## A typical Sherrelwood furnace-to-heat-pump conversion

Sherrelwood: Closed 100-amp panel with a clamp meter on the bench below.

The same scene in a thermal view.

Project price

$13,400

On site

2 days

Where

Sherrelwood

The house

Late-1960s brick ranch with basement, 100 A panel

Sherrelwood's houses are mostly from the late 1960s, and many still run on the 100-amp service they were built with. This brick ranch had a 22-year-old AC that was failing and a gas furnace that was only about 12. The owners wanted to heat with a heat pump, and the panel decided how.

We ran a load calculation on the electrical service before choosing any equipment. With a gas dryer and an electric range, the 100-amp panel had room for a 25-amp heat-pump circuit, but not for a 10 kW electric strip on top of it. A service upgrade to 200 amps made an all-electric system possible, and we priced that option, but the owners decided not to take on the cost and disruption for now.

That made this a dual-fuel conversion. The furnace stayed and became the backup, and a matched cased coil went on top of it in the basement. The heat load calculation and the small 1960s duct system both pointed to 2 tons, so a 2-ton cold-climate heat pump went on a new pad where the old condenser had been. Rather than core a new hole through the brick, we ran the 15-foot line set through the existing sleeve. A full-size two-pole breaker took the panel's last open spaces, and we labeled it in the directory.

After the county inspection we commissioned the system and set the changeover so the furnace runs only in the coldest weather.

## What a heat pump costs in Sherrelwood

Our prices are the same across the service area; your house sets where in the range you land. The panel and the ducts move the number most here. The [cost page](https://sundogauroraheatpumps.com/heat-pump-installation-cost/) breaks down what sits inside each figure.

| Work | Sundog's typical range |
| --- | --- |
| Cold-climate ducted heat pump, suitable existing ducts | $13,000 to $25,000 |
| Dual fuel with a new gas furnace and cold-climate heat pump | $19,000 to $28,000 |
| Ductless, one zone | $4,500 to $9,500 |
| Heat pump repair, routine | $150 to $1,200 |

## Nearby areas we serve

### Welby

Another unincorporated Adams County community just to the east, where homes date from the mid-1970s on average and permits also go through the county. [Welby service area](https://sundogauroraheatpumps.com/service-areas/welby-cdp/).

### Federal Heights

An incorporated city on Sherrelwood's north side, so its permits run through the city. [Federal Heights service area](https://sundogauroraheatpumps.com/service-areas/federal-heights-city/).

### Berkley

A short drive south, with housing a decade younger on average and the same Adams County permit path. [Berkley service area](https://sundogauroraheatpumps.com/service-areas/berkley-cdp/).

## Start with the panel and the ducts

Tell us what heats the house now and which rooms bother you. A photo of the panel label and the furnace nameplate helps. Call [(719) 417-2475](tel:+17194172475) or [book a visit](https://sundogauroraheatpumps.com/contact/).

## Heat pump questions in Sherrelwood

### What does a heat pump cost in Sherrelwood?

Sundog's typical range for a cold-climate ducted heat pump on suitable existing ducts is $13,000 to $25,000, and dual fuel with a new gas furnace runs $19,000 to $28,000. Keeping a sound furnace usually lands lower. The site visit and written estimate set your number.

### Can my 100-amp panel handle a heat pump?

Often yes for the outdoor unit, and often no for a large electric backup strip as well. A load calculation on the panel answers it. When the strip does not fit, dual fuel on your existing furnace is the usual way forward.

### Who issues the permit for a Sherrelwood address?

Sherrelwood is unincorporated, so mechanical and electrical permits go through Adams County. We confirm the permit path and inspections for your specific address before scheduling.

### My house has electric baseboard heat. Is a heat pump still an option?

Yes. Ductless heads are the usual fit for a house without ducts, sized room by room. The panel calculation starts from what the baseboards draw today, since the heat pump replaces most of that load.

### Do I need to replace the ducts in an older house?

Usually not all of them. We read static pressure and check the return first. Many older systems need a larger return or a few repaired runs rather than new ductwork throughout.

## Heat pump guides for this area

Electrical panel

Not always. The answer comes from the nameplate on the new equipment, what is already on your panel and a load calculation, not from the panel's size alone.

Ductwork for heat pumps

Most Aurora houses with a furnace already have ducts a heat pump can use.

Backup heat

Backup heat covers the hours a heat pump cannot carry the house alone.

## Nearby areas

Welby

Several heat pump faults look the same from inside the house.

Federal Heights

Small closets, close neighbors and a lot of electric heat.

Berkley

How much of January can a heat pump carry in your house?
