Last Updated: November 2026
Usually, yes. Your ducts can handle a heat pump if they carry the airflow it needs, typically around 350 to 450 cubic feet per minute per ton, at a static pressure the blower can work against. Many residential blowers are rated at 0.5 inches of water column. A weak return, crushed flex or leaky joints are the usual problems, and most are fixable.
Every Sundog estimate visit includes a static-pressure reading and a look at returns and leaks, and any duct work we find goes on the written estimate as its own line.
Why a heat pump is fussier about ducts than a furnace
The difference comes down to the temperature of the air in the ducts.
A gas furnace
Delivers very hot air, so even a reduced airflow still carries plenty of heat. Tired ducts hide behind it for years.
A heat pump
Delivers air that is warm rather than hot, so it needs its full airflow to move the same heat. Lose a third of the air to a restricted return and the far bedrooms feel it straight away, and the equipment works harder. Our cold-weather guide explains the supply temperatures.
What we measure on the visit
Duct condition is judged from readings and a look at the system, starting at the blower and working out to the rooms.
- Total external static pressure at the blower, the single best summary of how hard the ducts are to push air through
- Return size and the number of returns, compared with the airflow the new system needs
- The filter rack: filter size, type and whether air slips around it
- The supply trunk and far runs for leaks, crushed or kinked flex and disconnected joints
- Ducts in attics, crawlspaces or garages, where leaks and missing insulation cost the most
- Which rooms run hot or cold, and what the owners already notice
Reading static pressure
Static pressure is measured in inches of water column. Lower means the ducts let the air through.
Near the rating
A reading near the blower's rated pressure, often 0.5, means the ducts can carry full airflow. The heat pump goes in without duct changes, or with small sealing work.
Well above it
A reading near 0.8 or higher means the blower is fighting the ducts. On the Littleton job on our ducted installation page the reading was about 0.9 before the return was fixed.
Want your own number? We start from your house and your bills.
Get an EstimateThe usual fixes, and how to spot the problem
When the reading is high we find out why before anyone orders equipment. These are the usual causes, and each fix goes on the estimate as its own line so you can see what it costs and why it is there.
| Problem | What you notice | The fix |
|---|---|---|
| Undersized return | Whistling grille, cold far rooms, a loud blower | A larger return or a second return upstairs |
| Crushed or sagging flex | One room never keeps up | Replace the run, often with rigid round duct |
| Leaky trunk joints | Dusty basement, uneven rooms | Seal joints with mastic or foil tape |
| Restrictive filter | High reading that drops with the filter out | A larger filter rack or a lower-resistance filter |
| Dirty indoor coil | Weak airflow everywhere | Coil cleaning, or replacement with the system |
When duct changes are worth it, and when they aren't
Duct work is evaluated against what it fixes. Not every house needs it, and some problems are cheaper to solve another way.
Worth doing before install
A high static reading, a single small return, or crushed runs to the rooms that already complain. These fixes let the new system deliver its rated airflow.
Worth weighing
Long runs to a room over the garage or an addition that was never on the duct system. A single ductless head may serve that room better than a new duct run; the ducted vs ductless guide compares them.
New ductwork
New runs are laid out with ACCA's Manual D method so each room gets the air its load calls for. That is a bigger job and priced separately.
Flex or rigid metal duct?
Both are allowed; how they are installed matters more than which one is used.
Rigid metal
Smooth inside, holds its shape and resists crushing. We favor it for returns and the trunk, where airflow is greatest.
Flex
Fine for short branches when pulled tight and supported. Long, sagging or kinked flex is a common airflow problem in older ranches and tri-levels.
Ducts in the attic, crawlspace or garage
Ducts that run through unheated space lose heat before it reaches the room, and a heat pump's warm-not-hot air has less to spare.
Where it shows up
Tri-levels and split-levels often run returns through a crawlspace, and rooms over garages are fed through cold framing. Leaks there pull cold air into the return or push warm air into the crawlspace.
What helps
Sealing the joints first, then insulating the runs that sit in cold space. The load calculation counts duct location, so fixing it can also trim the size of the system you need.
Know your ducts before you compare equipment
Two quotes for the same heat pump can perform very differently if only one fixes the return. Call Sundog at (719) 417-2475 or book a visit and we will measure your ducts first. For sizing, see heat pump sizing; for the whole plan, the Aurora planning guide.
Get an EstimateQuestions people ask
Do I need new ducts for a heat pump?
Rarely the whole system. Most Aurora houses need, at most, a larger or second return, a replaced run or sealing. We measure before recommending anything.
How often should I change the filter with a heat pump?
Check it monthly in heating and cooling season and change it when it looks gray, or at the interval the filter maker gives. A clogged filter raises static pressure and cuts airflow.
Will a heat pump fix a room that is always cold?
Only if the cause is fixed with it. A cold room usually traces to a restricted run, a leak or a weak return, which the visit finds.

