Decision Guide

What backup heat should a heat pump have in Colorado?

Backup heat covers the hours a heat pump cannot carry the house alone. The choice is between electric strips, a gas furnace, or a small backup, and your house and rates decide it.

New white heat pump air handler in a basement with refrigerant lines and a disconnectThe same house in a thermal rendering
Daylight and thermal views of the same house: where it loses heat sets the load.

Last Updated: November 2026

Most Colorado heat pumps use one of two backups: electric resistance strips in the indoor air handler, or a gas furnace in a dual-fuel setup. Some well-insulated houses with a strong cold-climate unit need only a small strip. Which fits depends on the house's heat loss, the unit's output at 5°F, your panel and your gas and electric rates.

No option is cheapest for every house. We size the backup to the gap our load calculation finds, and we show you the cold-night numbers before you choose between dual fuel and an all-electric system.

The three ways to cover the cold hours

Each option does the same job, heat for the hours below the balance point and during defrost, with different trade-offs. Backup also matters on the night something fails: if the outdoor unit stops, the backup is what keeps the pipes and the house warm until it is repaired, so we never size it to zero without talking it through.

Electric strip backupDual fuel (gas furnace)Small or no backup
How it worksResistance coils in the air handler switch on in stagesThe furnace takes over below a set outdoor temperatureThe heat pump carries nearly all hours; a small strip covers defrost
What it needsPanel capacity for the strip circuitA furnace in good shape whose blower and coil match the heat pumpLow heat loss and strong 5°F output
Running cost depends onYour electric rate; strips deliver 1 unit of heat per unit of electricityYour gas rate and furnace efficiencyMostly the heat pump's efficiency
Watch forStrips running when the heat pump can carry the loadA changeover set by habit, not by numbersA cold-snap shortfall if the load was guessed

Sizing electric backup to the gap

One kilowatt of resistance heat delivers 3,412 BTU per hour. That makes strip sizing simple arithmetic once the load calculation is done.

5 kW stripAbout 17,000 BTU per hour10 kW stripAbout 34,000 BTU per hour; roughly 42amps at 240 volts020,00040,000BTU per hour

The math

A 5 kW strip delivers about 17,000 BTU per hour; a 10 kW strip about 34,000. At 240 volts, 10 kW draws roughly 42 amps before the circuit is sized, which is why a strip that is bigger than the gap costs panel space it never uses.

Staging and lockout

Strips should come on in stages and stay locked out above an outdoor temperature where the heat pump can carry the house. Without a lockout, a thermostat can call for strips on a mild morning simply because the house is recovering. Our panel guide covers the circuits.

How a dual-fuel system decides which one runs

In a dual-fuel house the controls switch from heat pump to furnace at a changeover temperature. There are two ways to set it, and the better changeover uses both.

The comfort point

The balance point: the outdoor temperature where the heat pump stops keeping up with the house. Below it, the furnace has to take over or the house cools.

The cost point

Compare the cost of 100,000 BTU of delivered heat. From gas, that is one therm divided by the furnace's efficiency. From the heat pump, it is 29.3 kWh times your electric rate divided by the heat pump's COP at that temperature. We run it on your own Xcel rates.

Want your own number? We start from your house and your bills.

Get an Estimate

Controls make or break the backup

The same equipment can run efficiently or expensively depending on how the controls are set up. These are the settings we confirm at start-up and leave in writing with you.

  • An outdoor sensor, so changeover and lockout follow the actual temperature
  • Strip lockout above a set outdoor temperature, and staged strips below it
  • Defrost tempering, so the backup warms the air briefly while the coil defrosts
  • A thermostat that knows it is running a heat pump, with the right number of stages
  • Gentle recovery after a setback, so a morning warm-up doesn't bring on the strips

Should I turn the thermostat down at night?

With a furnace, deep setbacks save gas. With a heat pump, the answer depends on the backup and the controls.

Electric strip backup

A small setback of a few degrees, or none, usually works best. A deep setback can make the morning recovery call on the strips, the most expensive heat in the house.

Dual fuel

Setbacks behave more like they did with the furnace, because the furnace handles recovery on cold mornings. The changeover setting still matters.

Smart thermostats

Many offer a heat-pump recovery mode that warms the house slowly. We set it to match the backup you have.

Which backup fits which house

These are the places we start the conversation, not fixed answers.

Lean toward dual fuel

The furnace has good years left, the AC is the part that failed, or the panel has little room for a large strip. See furnace-to-heat-pump conversion if you are weighing it.

Lean toward electric backup

The furnace is near the end of its life, the house has room on the panel, you want to drop gas, and a cold-climate model covers most of the load at 5°F.

Lean toward a small backup

Newer, tighter houses with a low heat loss, where the 5°F output of the chosen unit covers the design load or nearly does. A small strip still covers defrost and a failed outdoor unit.

Choosing with your numbers

Bring a year of Xcel bills to the visit and we can set the changeover and size the strips from them. Call Sundog at (719) 417-2475 or request an estimate. The heat pump vs gas furnace guide and operating cost guide go deeper on the money side.

Get an Estimate

Questions people ask

Is electric backup heat expensive to run?

Per unit of heat, resistance strips cost more to run than a working heat pump, because they deliver one unit of heat per unit of electricity. Sized to the gap and locked out in mild weather, they run for a small share of the winter.

Can I keep my old furnace as the backup?

Often, if it is in good condition and its blower and coil can work with the heat pump. We check both on the visit; a furnace near the end of its life usually makes more sense to replace with the job.

Does backup heat come on during defrost?

In most setups, yes, briefly. It tempers the air while the outdoor coil defrosts so the registers don't blow cool air for those few minutes.

Get an estimate for your Aurora house

Tell us about the house and the rooms that give you trouble. We come back with a first range from our typical rates and a time for the site visit.

CallGet an Estimate