Last Updated: November 2026
The short answer
Sundog's typical range for a cold-climate ducted heat pump in Aurora is $13,000 to $25,000, set at the site visit and confirmed in a written estimate. Where your job lands depends on how much heat the house loses, whether the ducts carry the airflow, what the panel can take and how backup heat is handled.
Rebates come off afterward. We quote the full installed price first, then show each incentive that applies to your address as its own line, so you can see both numbers. If you are early in the decision, the Aurora planning guide walks the whole choice in order.
Our typical ranges by system
These are the ranges we budget from before we see the house. Each one assumes the conditions we usually meet in Aurora-area homes. The visit replaces the range with your number: we measure the rooms, test the ducts and read the panel, and the written estimate lists what we found.
| System | Sundog's typical range | What usually puts a job near the top |
|---|---|---|
| Cold-climate ducted heat pump, existing ducts that carry the airflow | $13,000 to $25,000 | Larger capacity, a new air handler with staged electric backup, return or duct repairs |
| Dual fuel with a new gas furnace and cold-climate heat pump | $19,000 to $28,000 | Furnace venting changes, a relined water-heater flue, a tight furnace room |
| Ductless, one zone | $4,500 to $9,500 | Cold-climate head, a long line run, a new circuit from a full panel |
| Ductless, two to four heads | $9,000 to $18,000 | Heads on different floors, several line-set routes, ceiling cassettes |
| Ductless, five to eight heads | $18,000 to $35,000 and up | Whole-home coverage, more than one outdoor unit |
| Heat pump repair | $150 to $1,200 routine; $1,500 to $3,500 for major components | Compressor or reversing valve, refrigerant recovery and recharge |
| Ductless repair | $150 to $1,500 | Refrigerant leaks at flare joints, control boards, condensate pumps |
| Maintenance visit | $100 to $200; ductless $89 to $200 | Several heads, coil cleaning in place, a drain that needs clearing |
| Commercial heat-pump work | Priced per building after a survey | Rooftop access, crane lifts, feeders, phasing around tenants |
Ductless rooms that must hold heat in a cold snap
When every head in the plan is a cold-climate model, we budget by the number of zones. These figures sit inside the broader ductless ranges above; the wider ranges also cover harder installs such as long line runs or a finished wall to cross. Our zone planning guide explains how the zones are drawn.
One zone
Sundog's typical range is $4,500 to $6,500. A bonus room, a sunroom or one cold bedroom.
Two zones
Sundog's typical range is $8,500 to $12,500. Usually two bedrooms, or a bedroom and a basement room.
Three zones
Sundog's typical range is $12,500 to $18,500. A floor of a tri-level or a finished basement split into rooms.
Four or five zones
Sundog's typical range is $17,500 to $26,000. Most of a house without ducts, sometimes on two outdoor units.
What moves a price inside the range
Two houses with the same size heat pump can land thousands apart. The equipment is rarely the whole difference; the work around it is. These are the items we check on the visit and price as separate lines.
| Factor | What we check | Why it changes the price |
|---|---|---|
| Heat loss and capacity | Room-by-room load calculation | Sets the tonnage; the old nameplate is often a size too big |
| Cold-weather rating | Published output at 5°F | Models that hold capacity in the cold cost more and need less backup |
| Ducts and returns | Static pressure, leaks, crushed runs | A second return or rigid replacement run is added labor and material |
| Panel and circuits | Panel rating and open spaces | Electric backup can need a 45 to 60 amp circuit; a full panel can need more work |
| Backup heat | Furnace condition or strip size | Keeping a sound furnace avoids a new one; a new furnace adds venting work |
| Line set and outdoor spot | Distance to the indoor unit, snow and drip lines | Long runs need extra refrigerant; a raised stand costs more than a pad |
| Access | Furnace room, attic, crawlspace | Tight basements and attic routes add hours |
| Permits | Mechanical and electrical scope | Aurora sets each fee by scope |
Want your own number? We start from your house and your bills.
Get an EstimateWhat's inside an Aurora heat pump price
Some parts of a price have public figures behind them and some do not. Where an agency publishes the input, it is named below. Where there is no public figure, the part is scope we check at your house.
| Part of the price | What sets it | Local figure |
|---|---|---|
| Equipment | Capacity at 5°F, variable-speed or staged, matched coil or air handler | Set by the model chosen; model numbers and low-temperature capacity go on the estimate |
| Installation labor | Days on site, plus duct and electrical work found on the visit | Median $34.41 an hour locally, $29.33 nationally (U.S. Bureau of Labor Statistics) |
| Mechanical permit | Permit type, scope and valuation | Set by the City of Aurora fee schedule and fee calculator |
| Electrical work and permit | New circuits, disconnect, any panel work | Aurora reviews new electrical permits under the 2026 National Electrical Code (City of Aurora Building Division) |
| Code-required details | Condensate disposal, clearances, line-set protection | Aurora inspects mechanical work under the 2021 International Mechanical Code |
| Removal and refrigerant | Old furnace, coil and outdoor unit | Refrigerant must be recovered under federal rules (EPA Section 608) |
| Ductwork | Returns, sealing, crushed or undersized runs | Set by the scope we find at the visit |
| Pad, stand and patching | Snow line, drip line, wall and drywall repair | Set by the scope we find at the visit |
Labor is the clearest public input. HVAC mechanics and installers in the Denver-Aurora-Centennial metro earn a median $34.41 an hour, about 17% above the $29.33 national median, according to the U.S. Bureau of Labor Statistics. A wage is not a billing rate: the rate billed for an installer's hour also carries insurance, licensing, vehicles, tools and overhead.
Rebates and credits, kept apart from the price
Incentives change during the year and depend on the address, the equipment and who installs it. That is why we never fold them into a range. We check what applies to your address before the estimate is final, and the rebates guide explains each program in more depth.
| Program | Who runs it | What decides eligibility | How it reaches you |
|---|---|---|---|
| Residential heat-pump rebate | Xcel Energy | Xcel service address, qualifying equipment installed by a participating contractor, installation and application deadlines | Paid after the job; check the current program dates |
| Aurora F-3 project | Xcel Energy | A mapped area of Aurora with active Xcel gas service and a participating contractor | Address check before the estimate |
| Colorado Heat Pump Tax Credit | Colorado Energy Office | The installing contractor must be registered with the state | A discount shown as its own line on the invoice |
| Colorado Home Energy Rebates | Colorado Energy Office | Household income, a registered contractor and remaining regional funding | Check current availability for your county |
| Federal 25C tax credit | IRS | Ended for systems installed after 2025 | No longer applies |
Three typical budgets
These three typical budgets show how the ranges turn into single prices. Each one is priced from the house, not the label on the old equipment.
All-electric ducted, Denver ranch: $18,400, three days
A late-1950s brick ranch with an 80% furnace and an old AC. A 3-ton cold-climate heat pump on a raised pad, a variable-speed air handler with an 8 kW strip in the furnace spot, a second return from the living room and new 30 and 45 amp circuits. The added return and the strip circuit are what lift it above the bottom of the range.
Dual fuel with a new furnace, Hoffman Heights: $23,800, two days
The AC had failed and the 1990s furnace was near the end. A 96% furnace, a matched coil and a 3-ton cold-climate heat pump, one size smaller than the old system, plus a repaired return to the back bedroom and a 40-amp circuit. The new furnace and its venting put this job in the upper half of the dual-fuel range.
Three-head ductless, Northglenn tri-level: $15,800, three days
A mid-1970s tri-level with two cold upstairs bedrooms and a lower family room. A 2-ton multi-zone outdoor unit, three wall heads sized room by room, three line sets in exterior line-hide and one dedicated 240-volt circuit. Three separate line routes are most of the labor.
How the written estimate turns a range into your price
The installation process starts with a visit: a room-by-room load calculation, duct and airflow checks and a panel check. The written estimate then puts every part of the job on its own line, so two quotes can be compared item by item instead of by the total.
- Model numbers for the indoor and outdoor units, with capacity at low temperatures
- Duct work found on the visit, such as a new return or sealed joints
- Electrical circuits, the disconnect and any panel work
- The permit
- Removal of the old equipment with refrigerant recovered
- The pad or stand
- Start-up checks for airflow, charge and controls
- Incentives that apply to your address, listed apart from the price
Get your own number
Call (719) 417-2475 or send us the details of the house and the equipment you have now. Photos of the furnace label and the panel help. We come back with a first range from these figures and book the visit, and the cost estimator shows where your system type usually falls before you call. If you are weighing gas against electric first, start with heat pump or gas furnace, or see what ducted heat pump installation includes.
Get an EstimateQuestions people ask
Does the range include rebates?
No. Our ranges are installed prices before any incentive. We list each rebate or discount that applies to your address as its own line, so you see the full price and what comes off it.
Why do two quotes for the same size heat pump differ by thousands?
Usually because one includes duct, electrical or backup-heat work the other leaves out, or because the equipment differs in cold-weather output. Compare model numbers, capacity at 5°F and each work line, not just the total.
Is a panel upgrade inside the typical range?
A new circuit is. A full panel replacement is not always, because it depends on the panel's rating and what is already on it. We check the panel on the visit and price any upgrade as its own line.
Are permits included in the price?
Yes. The mechanical permit and any electrical permit go on the written estimate as a line. Aurora sets the fee by scope through its fee schedule.

