Last Updated: November 2026
Last Updated: November 2026
In Sherrelwood the question is rarely whether a heat pump can heat the house. It is whether the electrical panel and the ducts can carry one. Sundog plans heat pump installation in Sherrelwood starting from those two things: a load calculation on the panel, a static-pressure reading at the furnace and a room-by-room heat load, all on the first visit.
From there you choose between keeping your furnace as backup, going all-electric with a service upgrade, or adding ductless heads where the ducts fall short. Every option goes on the written estimate with its own price.
Where Sherrelwood calls usually start
The housing here is older than in most of the north metro, so the calls tend to circle the same few situations.
The AC is failing and the furnace is fine
A heat pump replaces the AC and takes over most of the heating, while the furnace stays for the coldest nights. This is the most common conversion path for a house with a younger furnace.
The panel looks full
A 100-amp panel with a gas dryer often has room for one outdoor-unit circuit but not an electric backup strip. We work that out with a load calculation, not by counting empty slots.
Some rooms never keep up
Duct systems from this era were sized for furnace air. A heat pump moves more air at a lower supply temperature, so a weak branch shows up fast. We read static pressure before we choose a size.
The house heats with electricity now
About a quarter of Sherrelwood homes heat with electricity. Replacing resistance heat with a heat pump is a different job from a gas conversion, and the panel math changes with it.
What we do for Sherrelwood houses
Ducted and dual fuel
A ducted heat pump on your existing ducts, or a dual-fuel system that keeps the furnace as backup. We choose cold-climate equipment by its published output at 5°F, so the furnace runs fewer hours.
Ductless, repair and upkeep
Ductless heads for a converted garage, a basement bedroom or a room the ducts never reached. In a basement bedroom the lines usually run through the joist bays to an outdoor unit on the side yard. We also handle heat pump repair and yearly maintenance for systems already in place.
How a Sherrelwood job usually runs
Each step leaves you with something in writing before the next one starts.
The visit
Room loads, a static-pressure reading at the furnace, the duct runs you can reach, and the panel: its rating, what is on it and what it carries on a cold evening.
The options
If the panel limits backup heat, you see two paths priced side by side: dual fuel on the panel you have, or all-electric with a service upgrade.
Permits
Sherrelwood is unincorporated, so the mechanical and electrical permits come from Adams County, not a city. We confirm the permit path for your address before work is scheduled.
Install and start-up
Old condenser out, coil and outdoor unit in, circuit wired, system charged and tested. Start-up readings, model numbers and rebate paperwork stay with you.
What we look for in a Sherrelwood house
Three things about Sherrelwood shape most estimates here, and each one comes from the age and makeup of the housing.
Housing from the late 1960s
The Census Bureau's American Community Survey puts Sherrelwood's median year built at 1967, among the oldest of the places we serve. Houses from that period often still have their original service size and duct layout. That tells us nothing certain about your house, but it tells us where to look first: the panel, the return and the far rooms.
Mostly gas heat, with a real electric share
About 71% of occupied homes here heat with utility gas and about 25% with electricity. For the gas homes, the decision is usually how much of the heating the heat pump takes on. For the electric homes, a heat pump replaces resistance heat, and the panel calculation starts from what the old heaters already draw.
County rules, checked per address
Sherrelwood is a census-designated place inside Adams County, with no city government of its own. For permits applied for from July 1, 2026, unincorporated Adams County uses the 2024 International Mechanical Code and the 2023 National Electrical Code. Fees and inspections follow the county's process, and we confirm both for your address.
Dual fuel or all-electric on an older panel
Most Sherrelwood conversions come down to this choice, and the panel usually makes it. Here is how the two paths differ once the load calculation is done.
Dual fuel on the panel you have
The heat pump needs one dedicated circuit, often 25 or 30 amps. The furnace stays as backup, so no electric strip is needed and the service size stays the same. It suits a furnace with years left and a panel with a little room. You keep a gas bill, and the changeover temperature decides how much of the winter runs on the heat pump.
All-electric with a service upgrade
An air handler with an electric strip replaces the furnace, which takes far more panel capacity than the heat pump alone. On a 100-amp service that usually means an upgrade, and the utility has its own steps for that. We price the upgrade as a separate line so you can weigh it against keeping gas. Our panel guide explains the circuits.
Why we measure before we price
- A panel load calculation decides between dual fuel and all-electric before you spend money on either.
- Sizing from the room loads, not the old condenser label, keeps a small 1960s duct system from being asked for more air than it can move.
- Reusing an existing wall sleeve or line route where it is sound saves coring through brick or block.
- We price a service upgrade as its own line, so you can see what all-electric costs against keeping the furnace.
- Rebate eligibility depends on your address, equipment and installer path, so we check it before the estimate is final. See our rebate guide.
A typical Sherrelwood furnace-to-heat-pump conversion


- Project price
- $13,400
- On site
- 2 days
- Where
- Sherrelwood
- The house
- Late-1960s brick ranch with basement, 100 A panel
Sherrelwood's houses are mostly from the late 1960s, and many still run on the 100-amp service they were built with. This brick ranch had a 22-year-old AC that was failing and a gas furnace that was only about 12. The owners wanted to heat with a heat pump, and the panel decided how.
We ran a load calculation on the electrical service before choosing any equipment. With a gas dryer and an electric range, the 100-amp panel had room for a 25-amp heat-pump circuit, but not for a 10 kW electric strip on top of it. A service upgrade to 200 amps made an all-electric system possible, and we priced that option, but the owners decided not to take on the cost and disruption for now.
That made this a dual-fuel conversion. The furnace stayed and became the backup, and a matched cased coil went on top of it in the basement. The heat load calculation and the small 1960s duct system both pointed to 2 tons, so a 2-ton cold-climate heat pump went on a new pad where the old condenser had been. Rather than core a new hole through the brick, we ran the 15-foot line set through the existing sleeve. A full-size two-pole breaker took the panel's last open spaces, and we labeled it in the directory.
After the county inspection we commissioned the system and set the changeover so the furnace runs only in the coldest weather.
What a heat pump costs in Sherrelwood
Our prices are the same across the service area; your house sets where in the range you land. The panel and the ducts move the number most here. The cost page breaks down what sits inside each figure.
| Work | Sundog's typical range |
|---|---|
| Cold-climate ducted heat pump, suitable existing ducts | $13,000 to $25,000 |
| Dual fuel with a new gas furnace and cold-climate heat pump | $19,000 to $28,000 |
| Ductless, one zone | $4,500 to $9,500 |
| Heat pump repair, routine | $150 to $1,200 |
Nearby areas we serve
Welby
Another unincorporated Adams County community just to the east, where homes date from the mid-1970s on average and permits also go through the county. Welby service area.
Federal Heights
An incorporated city on Sherrelwood's north side, so its permits run through the city. Federal Heights service area.
Berkley
A short drive south, with housing a decade younger on average and the same Adams County permit path. Berkley service area.
Start with the panel and the ducts
Tell us what heats the house now and which rooms bother you. A photo of the panel label and the furnace nameplate helps. Call (719) 417-2475 or book a visit.
Get an EstimateHeat pump questions in Sherrelwood
What does a heat pump cost in Sherrelwood?
Sundog's typical range for a cold-climate ducted heat pump on suitable existing ducts is $13,000 to $25,000, and dual fuel with a new gas furnace runs $19,000 to $28,000. Keeping a sound furnace usually lands lower. The site visit and written estimate set your number.
Can my 100-amp panel handle a heat pump?
Often yes for the outdoor unit, and often no for a large electric backup strip as well. A load calculation on the panel answers it. When the strip does not fit, dual fuel on your existing furnace is the usual way forward.
Who issues the permit for a Sherrelwood address?
Sherrelwood is unincorporated, so mechanical and electrical permits go through Adams County. We confirm the permit path and inspections for your specific address before scheduling.
My house has electric baseboard heat. Is a heat pump still an option?
Yes. Ductless heads are the usual fit for a house without ducts, sized room by room. The panel calculation starts from what the baseboards draw today, since the heat pump replaces most of that load.
Do I need to replace the ducts in an older house?
Usually not all of them. We read static pressure and check the return first. Many older systems need a larger return or a few repaired runs rather than new ductwork throughout.

