Heat Pump Repair and Service in Welby, CO

Several heat pump faults look the same from inside the house. A test tells them apart before any part is ordered.

Heat pump outdoor unit in the side yard of a Welby ranchThe same house in a thermal rendering
Daylight and thermal views of the same house: where it loses heat sets the load.

Last Updated: November 2026

Sundog repairs and services heat pumps in Welby, the unincorporated Adams County community in the 80229 ZIP code. When a heat pump blows cool air in January, ices over or trips a breaker, the first job is finding the cause, because several faults look the same from inside the house. We test before we replace anything, and we tell you what the test showed.

Sundog's typical range for heat pump repair is $150 to $1,200 for routine work such as capacitors, contactors, sensors and drains, and $1,500 to $3,500 for major components such as a reversing valve or a compressor. When a repair stops making sense, we price replacement next to it so you can compare.

Symptoms Welby owners call about

Each symptom has more than one possible cause. These are the ones we rule in or out first.

Cool air from the vents in heat mode

It can be a normal defrost cycle, low charge, a stuck reversing valve or a failed coil on that valve. Frost and defrost explains what is normal.

Ice that will not melt off

Thin frost that clears during defrost is normal. A thick ridge around the base often comes from roof meltwater or a blocked base-pan drain, and it needs attention before it damages the coil or fan.

The breaker trips when the system starts

A failing capacitor, shorted wiring or a compressor drawing too much current can all trip it. Resetting it again and again can make the damage worse, so it is worth a test.

Heating only on the backup strip

The house stays warm but the bill climbs. The outdoor unit may not be contributing at all, and an electrical and refrigerant test usually shows why.

Heat pump services in Welby

Sundog provides these heat pump services in Welby:

How a Welby repair call usually runs

  1. Symptoms first

    Tell us what the system does, when it started and what the thermostat shows. Thermostat settings, breaker trips and ice patterns all narrow the cause before we arrive. A photo of the outdoor unit and its label helps too, since age and refrigerant type shape the repair-or-replace question.

  2. Tests

    Voltage at the controls and the reversing-valve coil, capacitor and compressor readings, refrigerant pressures and line temperatures.

  3. Written price

    The repair and its parts, whether a permit applies, and replacement priced alongside when the system is old or the part is major.

  4. Repair

    Refrigerant recovered where the work requires it, parts brazed under nitrogen, then a pressure test and evacuation before recharge.

  5. Proof

    Heating, cooling and a forced defrost run before we leave, with the readings left with you. Those readings become the baseline for the next maintenance visit, so a slow leak or a weakening part shows up as a change rather than a surprise.

Welby homes and Adams County rules

Welby is a compact unincorporated area of about four square miles, and both its housing and its jurisdiction affect a repair call.

Houses from the 1970s

Census estimates put the median year built at 1974, give or take two years. A heat pump in a house of that age is usually a later addition, set beside or in place of the original equipment, so the outdoor unit can be much newer than the ducts and wiring it connects to. We check both sides of the system before blaming the newest part.

Mostly gas, some heat pumps

About 75.8% of occupied homes heat with utility gas and 21.3% with electricity. In a gas home a failed heat pump often has a furnace to fall back on. In an all-electric home the backup strip carries the whole house until the repair is done, and the bill shows it. Our backup heat guide explains why strip heat costs more to run than the heat pump it is standing in for.

Adams County permits

Welby is governed by Adams County, so permits come from the county's Building Safety division, not a city. The county requires a permit to install, repair, convert or replace mechanical, gas and electrical systems, and it requires contractors to register before pulling one. From July 1, 2026, new county applications are reviewed under the 2024 International Mechanical Code and the 2023 National Electrical Code. We tell you on the written price whether your repair needs a permit.

Why we test before replacing

Testing first means you pay for the part that failed, not the one that was easiest to swap.

Cheap causes first

A valve coil that does not pull in costs far less than a valve that will not shift, and a capacitor less than a compressor. The tests tell them apart in minutes, so the cheaper fix is never skipped.

Repair or replace, both on paper

On an older system with a major failure, we price both and note the refrigerant type and system age. Our repair or replace guide shows how we weigh them.

Inside a Welby reversing-valve repair

Technician working inside an outdoor unit with its fan top set aside
Welby: Technician working inside an outdoor unit with its fan top set aside.
The same scene in a thermal rendering
The same scene in a thermal view.
Project price
$2,650
On site
6 hours
Where
Welby
The house
Mid-1970s ranch with basement

A heat pump blowing cool air in January can have several causes, so we tested before we replaced anything. This mid-1970s Welby ranch had a nine-year-old heat pump on its back wall, and the basement air handler's 10 kW strip was doing all the heating.

The solenoid coil on the reversing valve got 24 volts and pulled in when the thermostat called for heat. Temperatures on the lines around the valve showed it wasn't shifting, and the compressor and charge read healthy. That ruled out the cheaper coil fix and pointed to the valve itself. On a system this age, replacing one major component makes more sense than replacing the whole system.

The setting added work. The unit sat about 10 inches from the wall, under an eave with no gutter, and meltwater had built an ice ridge around its base. We chipped the ice, cleared the base pan drain, and removed the top and fan to reach the valve, which sat deep beside the compressor. After recovering the refrigerant we brazed in the new valve under flowing nitrogen with a wet rag on the body, because too much heat warps the slide inside. A new filter-drier went in, then a nitrogen pressure test and a vacuum held below 500 microns. Cold days slow that step, so we held the vacuum longer. The charge went back in by weight.

We ran the system in heating, forced a defrost cycle, and recommended a gutter or diverter over the unit.

The outdoor unit's surroundings matter

As foundCorrected
  1. Eave with no gutter drips meltwater onto the unit
  2. Meltwater refreezes around the base
  3. Gutter or diverter over the unit
  4. Stand lifts the unit above the snow line

Many winter repair calls start outside, not in the equipment. An outdoor unit set too close to the wall, under an eave with no gutter, or on a pad that sits in a low spot collects meltwater that refreezes around its base. Ice in the base pan can block the drain, stress the coil and stop the fan.

On a repair visit we look at where the unit sits as well as what failed. Where meltwater is the cause, we recommend a gutter or diverter over the unit, a stand that lifts it above the snow line, or clearing the base-pan drain, and we explain which one fixes the cause rather than the symptom. Our outdoor unit placement article covers the clearances.

Repair and service prices in Welby

These are Sundog's typical ranges. The diagnosis sets the repair price, and the written price comes before any work.

WorkSundog's typical range
Heat pump repair, routine$150 to $1,200
Heat pump repair, major components$1,500 to $3,500
Ductless repair$150 to $1,500
Heat pump maintenance visit$100 to $200

Describe the symptom

Tell us what the system is doing, when it started and whether a breaker has tripped. If the house is running on its backup strip alone, mention it, since that changes what we test first. Call (719) 417-2475 or get an estimate.

Get an Estimate

Heat pump questions in Welby

How much does heat pump repair cost in Welby?

Sundog's typical range for routine heat pump repair is $150 to $1,200, and major components such as a reversing valve or compressor run $1,500 to $3,500. Ductless repair is $150 to $1,500. The diagnosis sets your price, and you get it in writing before work starts.

Is a repair worth it on an older heat pump?

For a small part, usually yes. For a major part on a system near the end of its life, or one on R-22, replacement often makes more sense. We price both so you can compare.

Does Adams County require a permit for a heat pump repair?

The county's permit rules cover repairing, converting and replacing mechanical, gas and electrical systems, so some repairs need one. Whether yours does depends on the work, and we state it on the written price.

Why is my heat pump blowing cool air in heat mode?

It can be a normal defrost cycle, which ends in a few minutes. If it continues, the cause can be low charge, a reversing valve that will not shift, a failed valve coil or a control fault. Testing tells them apart.

Do you also maintain heat pumps in Welby?

Yes. Sundog's typical range for heat pump maintenance is $100 to $200 per visit, covering filters, coils, drains, electrical checks and charge and airflow readings, plus a look at ice and drainage around the outdoor unit.

Nearby areas

Get an estimate for your Welby house

Tell us about the house and the rooms that give you trouble. We come back with a first range from our typical rates and a time for the site visit.

CallGet an Estimate